Search found 3055 matches

by Deano
Mon Mar 20, 2017 8:15 pm
Forum: Airboat Talk
Topic: Injured Florida State Trooper
Replies: 5
Views: 505

Re: Injured Florida State Trooper

Will do. Thanks for the update.

Keep 'em coming when you have the chance.
by Deano
Mon Mar 20, 2017 4:30 pm
Forum: Airboat Tech
Topic: Plan design foar airboat France
Replies: 12
Views: 452

Re: Plan design foar airboat France

My 300 hp minimum guess was in reference to your initial 16' projection and its load. If you cut back to 12' and minimize your load, then your 150 hp could work if you keep it light. Be aware that the Glen-L you linked above, is not built or braced enough for such an engine. I've not seen those plan...
by Deano
Mon Mar 20, 2017 4:10 pm
Forum: Aircraft Power Only
Topic: 220 bogs and loses power at wide open throttle.
Replies: 25
Views: 586

Re: 220 bogs and loses power at wide open throttle.

Have you run it, bogged it out and shut it down in one motion, and then read the plugs? Doing so should confirm or deny your flooding theory. It sounds like, and odds would seem better it isn't getting enough gas. Are you sure the float level is set correctly? Sure your gauge is accurate? Holleys ar...
by Deano
Sun Mar 19, 2017 9:49 pm
Forum: Airboat Talk
Topic: Injured Florida State Trooper
Replies: 5
Views: 505

Re: Injured Florida State Trooper

Prayers sent that all those involved may arrive at the best possible outcome.
by Deano
Sun Mar 19, 2017 8:21 pm
Forum: Automotive Power Only
Topic: MTS VT59 Shaft Rocker System with ARP Studs Clearance Issue
Replies: 21
Views: 676

Re: MTS VT59 Shaft Rocker System with ARP Studs Clearance Issue

The ARP black oxide (8740 Chromoly) is what you want. I didn't go dig any out to measure them, but note that you're after three different lengths. Ten medium ones for the inside rows, and Two shorter for the ends and Eight long ones for the remainder of the outside rows. In other words, be aware the...
by Deano
Sun Mar 19, 2017 12:21 pm
Forum: Aircraft Power Only
Topic: 220 bogs and loses power at wide open throttle.
Replies: 25
Views: 586

Re: 220 bogs and loses power at wide open throttle.

Sounds like the prudent thing to do, and a safe bet to me.

I always like adding to the "Well, I know it's not that" list. :)
by Deano
Sun Mar 19, 2017 11:56 am
Forum: Automotive Power Only
Topic: MTS VT59 Shaft Rocker System with ARP Studs Clearance Issue
Replies: 21
Views: 676

Re: MTS VT59 Shaft Rocker System with ARP Studs Clearance Issue

I believe all that he was saying is that given that your rebuild is using the lower compression ratio, that head bolts will be sufficient. And that while studs may have been preferable, they are not mandatorily necessary for that level build. I kind of suspected that was grease on that stud . . . I ...
by Deano
Sun Mar 19, 2017 11:17 am
Forum: Aircraft Power Only
Topic: 220 bogs and loses power at wide open throttle.
Replies: 25
Views: 586

Re: 220 bogs and loses power at wide open throttle.

check your points gap......and coil may be weak x2 Beyond that, the general consensus seems to be #74 jets . . . http://southernairboat.com/phpBB3/search.php?keywords=%2B220+%2BHolley+%2B500+%2Bjets&terms=all&author=&sc=1&sf=all&sk=t&sd=d&sr=posts&st=0&ch=300&...
by Deano
Sun Mar 19, 2017 10:09 am
Forum: Aircraft Power Only
Topic: Need Help Alternator an Pulley 0435
Replies: 3
Views: 152

Re: Need Help Alternator an Pulley 0435

Good deal. :thumbleft:

You're in good hands . . .

. . . and without an Allstate Premium. :lol: :lol:
by Deano
Sun Mar 19, 2017 9:59 am
Forum: Automotive Power Only
Topic: MTS VT59 Shaft Rocker System with ARP Studs Clearance Issue
Replies: 21
Views: 676

Re: MTS VT59 Shaft Rocker System with ARP Studs Clearance Issue

Well, a couple of random thoughts/comments will not change what you've already determined, but if you wanted another mildly informed opinion that may be of little more than no value, I can help you out. :lol: First, you are to be commended for your photography skills, as all three pictures tell the ...
by Deano
Sat Mar 18, 2017 10:36 am
Forum: Aircraft Power Only
Topic: capacitor
Replies: 3
Views: 196

Re: capacitor

That middle one looks just like what OMC used on the old outboards.
by Deano
Sat Mar 18, 2017 10:32 am
Forum: Airboat Talk
Topic: OlfArt- Ken Johnson
Replies: 36
Views: 1589

Re: OlfArt- Ken Johnson

This is very sad news indeed. Ken was a great guy both on the board and otherwise.
He will definitely be missed. Prayers sent.
by Deano
Sat Mar 18, 2017 10:29 am
Forum: Aircraft Power Only
Topic: Need Help Alternator an Pulley 0435
Replies: 3
Views: 152

Re: Need Help Alternator an Pulley 0435

First couple to try that come to mind . . .

Norman Clay @Innovative Accessories
https://www.southernairboat.com/phpBB3/viewtopic.php?f=47&t=69530&p=674422
or
Dick Waters @ Air-Tec
http://www.airtecinc.us/airboat.html
by Deano
Tue Mar 14, 2017 5:56 pm
Forum: Airboat Tech
Topic: Plan design foar airboat France
Replies: 12
Views: 452

Re: Plan design foar airboat France

Glades Cat is correct on both counts.

There are no such plans available in the public domain, and 16' is a good sized airboat.

Probablement, au moins doubler votre estimation d’origine.
by Deano
Tue Mar 14, 2017 5:39 pm
Forum: Automotive Power Only
Topic: MTS VT59 Shaft Rocker System with ARP Studs Clearance Issue
Replies: 21
Views: 676

Re: MTS VT59 Shaft Rocker System with ARP Studs Clearance Issue

No questioning that makes sense, it wasn't something that occurred to me. I've used Harland Sharp, RAS, and some early MTS shaft systems and not had that issue. It wasn't something that I ever thought about before, but guess I never put studs in, AND shaft rockers on, an early block. :scratch: I hav...
by Deano
Sun Mar 12, 2017 6:27 pm
Forum: Automotive Power Only
Topic: MTS VT59 Shaft Rocker System with ARP Studs Clearance Issue
Replies: 21
Views: 676

Re: MTS VT59 Shaft Rocker System with ARP Studs Clearance Issue

That sounds like something is abnormal. I wouldn't want to shim them that far. Not only is that probably not preferable, but could be an issue if you already have pushrods and will only complicate VC clearance. Almost sounds like the wrong studs, but that seems more than unlikely from MTS. Did the m...
by Deano
Sun Mar 12, 2017 9:50 am
Forum: Automotive Power Only
Topic: 10.0:1 compression adding a blower optional?
Replies: 17
Views: 663

Re: 10.0:1 compression adding a blower optional?

My blower experience is limited, but from what I've seen and done, I would be inclined to purpose build another engine for the blower if that is an option. My assessment would be very similar to Swamphunter's friend in Tampa, in that lower compression will allow for more bang for the buck so to spea...
by Deano
Sun Mar 12, 2017 9:27 am
Forum: Airboat Talk
Topic: AAOF caretaker in fatal car accident.
Replies: 31
Views: 4631

Re: AAOF caretaker in fatal car accident.

It is a great man that leaves such a legacy, to be thought of so often even long after his passing.

Slide easy, my unmet friend . . . There is no questioning the example

you set for making the world a better place. God Bless you and yours.
by Deano
Fri Mar 10, 2017 11:30 am
Forum: Other Important News
Topic: Goodbye My Beautiful Baby
Replies: 15
Views: 658

Re: Goodbye My Beautiful Baby

Am at a complete loss for words. I can't imagine what you must be feeling. :cry:
Please know that you and your family are in our thoughts and our prayers.
by Deano
Tue Mar 07, 2017 9:44 am
Forum: Airboat Talk
Topic: Polyurea?
Replies: 13
Views: 758

Re: Polyurea?

Andy, If you would, please supply a link or some other info pertaining to the coating you're referring to. Always willing and wanting to learn new stuff and this is a new one to me. My exposure and knowledge of polyurea would not imply that it would be a good airboat bottom coating. Don't have anyth...
by Deano
Mon Mar 06, 2017 7:33 pm
Forum: Airboat Talk
Topic: HAPPY BIRTHDAY COWBOY!!!!!
Replies: 11
Views: 235

Re: HAPPY BIRTHDAY COWBOY!!!!!

Happy Birthday, Cowboy !

............ :occasion5:
by Deano
Mon Mar 06, 2017 5:24 pm
Forum: Airboat Talk
Topic: new hull and who to use
Replies: 13
Views: 739

Re: new hull and who to use

Given where you are, the first logical choice to consider would be American Airboats in Orange, Texas. Faron comes very highly recommended by many folks both here and elsewhere. It may or may not pan out as the best option, but it is certainly is the first one I would exhaust while researching my op...
by Deano
Sun Mar 05, 2017 1:02 pm
Forum: Airboat Talk
Topic: Who builds a nice galvanized trailer
Replies: 10
Views: 388

Re: Who builds a nice galvanized trailer

The first one that comes to mind is Cliff at B&S Trailers. I think his number is 352-591-2161.

I can't even figure out how old this one is (15+ years), but never had any grief with it.
by Deano
Sun Mar 05, 2017 12:07 am
Forum: Hunting & Fishing
Topic: Ban Bear Hunts for 10 years!!
Replies: 7
Views: 371

Re: Ban Bear Hunts for 10 years!!

It never ceases to amaze me that such flaming libtards can avoid spontaneous combustion. :shock: The literary masterpiece :scratch: referenced above is here in regular type: As state Rep. Amy Mercado declares, Florida’s now-annual black bear hunt has become a “slaughter.” Mercado and fellow Orlando...
by Deano
Wed Mar 01, 2017 8:31 pm
Forum: Aircraft Power Only
Topic: rebuild a 220
Replies: 3
Views: 287

Re: rebuild a 220

You might try calling Tom Jeffords and talk to him.
He's Speed Wheelie on this board. I believe his number is 863-956-3030.

Go to advanced search