lycoming wrenches

Aircraft powered airboat discussion.
toyman69
Southern Airboat Member
Posts: 98
Joined: Sun Aug 09, 2009 10:31 pm
Location: Hernando/Potts

lycoming wrenches

Postby toyman69 » Tue Aug 23, 2011 6:06 pm

Need to borrow wrenches to do a jug swap on a narrow deck 170. located in Citrus near Potts, thanks Sam 352-464-3410


chugalug
Site Supporter - II
Site Supporter - II
Posts: 259
Joined: Thu Nov 26, 2009 6:44 pm
Location: LAKE ALFRED FL. USA EARTH

Re: lycoming wrenches

Postby chugalug » Wed Aug 24, 2011 6:19 am

THEY DON'T LIKE TO LOAN NARROW DECK WRENCHES, CAUSE THE END WEARS OUT IF NOT USED CAREFUL. TAKE A 1/2 IN. & A 3/8 ALLEN WRENCH CUT ABOUT A 1/2 PIECE OF EACH , AND USE BOX END WRENCH WORKS GREAT DONE IT FOR YEARS. KIND OF PAIN IN A$$ TO DO REAR CYLS. TORQUE ONE GRUNT ON 3/8 STUDS, TWO GRUNTS ON 1/2 STUDS.

User avatar
goldhunter_2
Site Supporter - III
Site Supporter - III
Posts: 8935
Joined: Mon May 23, 2005 7:17 pm
Location: Port Saint Lucie Fl

Re: lycoming wrenches

Postby goldhunter_2 » Wed Aug 24, 2011 2:39 pm

chugalug wrote:TORQUE ONE GRUNT ON 3/8 STUDS, TWO GRUNTS ON 1/2 STUDS.


:lol: :lol: :lol: :lol: :lol:
.


Support our future , get a kid involved in the outdoors!!

:rebel:



.

User avatar
watersports7
Site Supporter - III
Site Supporter - III
Posts: 2523
Joined: Mon Dec 01, 2008 10:15 am
Location: Cocoa/PSJ/St Johns River

Re: lycoming wrenches

Postby watersports7 » Wed Aug 24, 2011 3:40 pm

German Torque Specification: *To be said with a German accent*

How tight did you torque down those lug nuts?

Good-N-Tight!
12' Predator / Lycoming 4 Cylinder / Old Skool 68x38 Stick Prop
Perfectly said by Lycoming: Some engines purr like kittens. These roar!

User avatar
HuntingBigun
Site Supporter - VIII
Site Supporter - VIII
Posts: 6250
Joined: Mon Jan 07, 2008 11:39 pm
Location: Plant City, FL
Contact:

Re: lycoming wrenches

Postby HuntingBigun » Wed Aug 24, 2011 4:00 pm

I never like to loan tools, boats or wife, they come back dirty, worn out or leaking something :D
Bigun

http://www.krvsa.com/index.html


Click for pics = http://www.flickr.com/photos/huntingbigun/

Killin Time 15.6 Diamondback Deckover Mast 808 Hp SC LS 7 /KRVSA /NRA


Trav-azz
Southern Airboat Member
Posts: 12
Joined: Tue Mar 01, 2011 8:09 pm

Re: lycoming wrenches

Postby Trav-azz » Wed Aug 24, 2011 4:29 pm

Www.ustools.com
$20 apiece a buddy of mine just order one after trying to borrow one for the last week. Watch the shipping cost though.

toyman69
Southern Airboat Member
Posts: 98
Joined: Sun Aug 09, 2009 10:31 pm
Location: Hernando/Potts

Re: lycoming wrenches

Postby toyman69 » Wed Aug 24, 2011 5:40 pm

Thanks guys, i am a heavy equipment mechanic, so i know what tools cost and how to take care of them. made wrench to fit all but one jug, just want job done right! i will look into ustools, Thanks for the replys Sam.

User avatar
nomad41
Site Supporter - VI
Site Supporter - VI
Posts: 4300
Joined: Tue Sep 18, 2007 5:12 pm
Location: Palmetto,Fl
Contact:

Re: lycoming wrenches

Postby nomad41 » Wed Aug 24, 2011 9:23 pm

its www.ustool.com no s after tool
http://www.flickr.com/photos/nomad41/
Treasurer FAA
Member:FAA, KRVSA ,IRCAA, FSCA,BAHCC,OAA
http://www.suncoastyachtservices.com
14.5x8 Diamondback ,SBC Stroker,2.68 Stinger,Sensenich 82" R
Svcliche@yahoo.com

chugalug
Site Supporter - II
Site Supporter - II
Posts: 259
Joined: Thu Nov 26, 2009 6:44 pm
Location: LAKE ALFRED FL. USA EARTH

Re: lycoming wrenches

Postby chugalug » Thu Aug 25, 2011 6:30 am

I WAS GOING TO GET MYSELF A SET, BUT NOT FOR 50 BUCKS APIECE. US TOOL $20 WIDE DECK, $50 NARROW DECK WRENCHES

josh_2562
Site Supporter - III
Site Supporter - III
Posts: 1521
Joined: Sun Aug 12, 2007 2:25 pm
Location: Inglis, FL 34449

Re: lycoming wrenches

Postby josh_2562 » Thu Aug 25, 2011 9:06 am

This is where I got mine. They work great.
http://www.aircraft-tool.com/shop/detai ... D=6494-SET
Paid $6.50 for shipping and got them in 3 days.

dusty burch
Southern Airboat Member
Posts: 317
Joined: Sat Jul 09, 2011 3:09 pm
Location: gainesville ,fl
Contact:

Re: lycoming wrenches

Postby dusty burch » Thu Aug 25, 2011 6:30 pm

if u buy the cheap ones they dont last the good ones r around $100 each but they will last a long time

mwood7800
Southern Airboat Member
Posts: 975
Joined: Thu Feb 03, 2005 5:32 pm

Re: lycoming wrenches

Postby mwood7800 » Thu Aug 25, 2011 9:11 pm

get the 100$ ones, the cheap ones suck, you will be lucky to do 6 cylinders with one set of cheapo's. I been there and tried it...

User avatar
mojoe
Southern Airboat Member
Posts: 755
Joined: Thu Jul 23, 2009 8:55 pm
Location: Catfish Motel

Re: lycoming wrenches

Postby mojoe » Tue Feb 07, 2017 9:39 pm

I have heard a couple guys drill out the hex wrenches and weld on 12 point bolts. The question is: Where do you fing good quality steel 12 point bolts to attach?

bbstimey
Southern Airboat Member
Posts: 277
Joined: Fri Jun 05, 2009 2:33 pm
Location: sebastian, fl

Re: lycoming wrenches

Postby bbstimey » Wed Feb 08, 2017 6:20 am

I replaced with ARP 12pt nut works much easier
14'x8' JB hull w/Stingered GO-480 w/ electronic ignition and 3 blade 80" R

User avatar
fhp6
Site Supporter - IV
Site Supporter - IV
Posts: 78
Joined: Wed Nov 11, 2009 8:25 pm
Location: Peachtree City, GA

Re: lycoming wrenches

Postby fhp6 » Wed Feb 08, 2017 8:24 am

bbstimey wrote:I replaced with ARP 12pt nut works much easier


Do you have a picture of the modified wrench you could post?
FHP6
Citrus County Airboat Alliance (Member)
"Lean Out"

Cmcintosh721
Southern Airboat Member
Posts: 165
Joined: Wed Jul 17, 2013 3:40 pm

Re: lycoming wrenches

Postby Cmcintosh721 » Wed Feb 08, 2017 1:23 pm

I bought a set from the Snap On man when I had my 0360 and they were not bad priced.

User avatar
mojoe
Southern Airboat Member
Posts: 755
Joined: Thu Jul 23, 2009 8:55 pm
Location: Catfish Motel

Re: lycoming wrenches

Postby mojoe » Wed Feb 08, 2017 4:02 pm

bbstimey wrote:I replaced with ARP 12pt nut works much easier



Thanks. Perfect.

bbstimey
Southern Airboat Member
Posts: 277
Joined: Fri Jun 05, 2009 2:33 pm
Location: sebastian, fl

Re: lycoming wrenches

Postby bbstimey » Thu Feb 09, 2017 6:27 am

fhp6 wrote:
bbstimey wrote:I replaced with ARP 12pt nut works much easier


Do you have a picture of the modified wrench you could post?



not a wrench changed nuts to arp they are 12pt on out side
14'x8' JB hull w/Stingered GO-480 w/ electronic ignition and 3 blade 80" R

User avatar
fhp6
Site Supporter - IV
Site Supporter - IV
Posts: 78
Joined: Wed Nov 11, 2009 8:25 pm
Location: Peachtree City, GA

Re: lycoming wrenches

Postby fhp6 » Thu Feb 09, 2017 9:09 am

Roger that...thank you!
FHP6
Citrus County Airboat Alliance (Member)
"Lean Out"

User avatar
mojoe
Southern Airboat Member
Posts: 755
Joined: Thu Jul 23, 2009 8:55 pm
Location: Catfish Motel

Re: lycoming wrenches

Postby mojoe » Thu Feb 09, 2017 10:46 am

Summit had them reasonable. Shipping was actually more money than the nuts. My plan is to modify the wrench. Drill a small center hole in the hex. Then grind it flat. Then set the ARP 12 point nut in its place, use the hole to visually center it on there and weld up the inside of the nut.

Mine has female 12 point nuts over the studs. So the tool/wrench needs to be male.

terrible ted
Southern Airboat Member
Posts: 2652
Joined: Tue Aug 12, 2008 8:07 pm
Location: orlando

Re: lycoming wrenches

Postby terrible ted » Thu Feb 09, 2017 12:47 pm

HuntingBigun wrote:I never like to loan tools, boats or wife, they come back dirty, worn out or leaking something :D




Not replying to this is chewing on me Could have so much fun with this. :twisted:

User avatar
mojoe
Southern Airboat Member
Posts: 755
Joined: Thu Jul 23, 2009 8:55 pm
Location: Catfish Motel

Re: lycoming wrenches

Postby mojoe » Sat Feb 11, 2017 8:29 pm

Turned out great. From a 6 point to a 12 point and ARP says those nuts are a lot harder than grade 8 steel. Really felt snug and fit all the way to the bottom of the bolt when I tested it.

Only "trick" was making sure to cut the nut in half before welding it on. That way I saved the bevel on the top and didn't have to grind it down to fit.
Attachments
IMG_1048.PNG
IMG_1047.PNG



Return to “Aircraft Power Only”

Who is online

Users browsing this forum: LIL Maddog and 3 guests