Search found 663 matches

by br,lc,LA
Sat Oct 19, 2019 9:04 am
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

I have no issues with idle using a short ram intake... but K&N filters suck... dry types are much better for MAF

Exhaust. Flange it to the turbo and hard pipe it all the way with a single flex joint close to the motor. Weld it out
by br,lc,LA
Fri Oct 18, 2019 5:36 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

Looking top notch!
by br,lc,LA
Tue Oct 15, 2019 7:53 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

Depends on boost pressure, timing, fuel type... colder is always better
by br,lc,LA
Tue Oct 15, 2019 4:45 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

Their IC0035
https://www.cxracing.com/IC0035?search=IC0035&limit=100

When its 90deg out my temps dont climb much above 100F still... I am pushing close to 300HP with the 1.4L now
by br,lc,LA
Tue Oct 15, 2019 2:39 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

I use summit to find the parts I need and then Amazon to order them with prime account. usually get a better price, but summit beats jegs by a mile when finding things.

I run CXRacing stuff on my Ecotec. No issue really... cheap but works.
by br,lc,LA
Wed Jul 31, 2019 7:04 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

In-tank pressure sensor is for vapor recovery system which you wont have installed. If you read the LTG Crate Motor instructions the inline sensor is included in the harness kit.
by br,lc,LA
Mon Jul 29, 2019 6:36 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

Don't think the PCM actually cares about low pressure side. It's basically a lift pump for the high pressure pump on these engines. Here's a few pics with a cracker in the back seat. :cheers: 20190629_153312.jpg 20190705_163612-EFFECTS.jpg Russ, Depends on the tune. Ill have to look back at the LTG...
by br,lc,LA
Mon Jul 29, 2019 10:24 am
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

Easily done with a tee, -6AN lines will be large enough for stock HP up to slightly molded. The LP FP sensor is a female thread. Part # 13579380
by br,lc,LA
Sun Jul 28, 2019 8:53 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

Just make sure the external pump can feed 50-60psi and it will work fine. Youll have to plumb the FP sensor into your system downstream of the regulator as the engine requires a fuel pressure input upstream of the HP pump. Make sure the regulator is located as close to the HP pump as possible so you...
by br,lc,LA
Fri Jul 12, 2019 8:03 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

skinny The B207 is an LK9 turbocharged version instead of the supercharged LSJ. You probably can find a good tuner and swap out the P12 (which you likely have) to a E67. https://www.cobaltss.net/forums/2-0l-lsj-performance-tech-47/want-run-e67-computer-your-lsj-powered-car-its-easy-304426/ ZZP may b...
by br,lc,LA
Fri Jul 12, 2019 6:40 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

Skinny... if you need an Ecotec breakdown here https://en.wikipedia.org/wiki/GM_Ecotec_engine Basically a 2.4 NA that tops out about 190-200HP... I make that with the 1.4L Turbo... Best bang for the buck is a LHU or newer LTG - 2.0L Turbo, but I looked at doing a new boat and just doesnt make since ...
by br,lc,LA
Mon Jun 03, 2019 3:30 pm
Forum: Automotive Power Only
Topic: anyone running a 350 with 2.1 box?
Replies: 42
Views: 3627

Re: anyone running a 350 with 2.1 box?

Torque is nothing but cylinder pressure x cylinder area x crank lobe offset It is absolutely useless number w/o rpm being involved and torque x rpm = HP If you want to run your engine at high torque which equals high cylinder pressure and lug the motor all the time... by all means let it blow! That'...
by br,lc,LA
Mon May 27, 2019 8:13 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

Those are the service manuals in HTML but the images like diagrams require a plug-in that works only for IE or Edge. If you want the actual full manuals in pdf youll need to go thru Helm http://www.helminc.com/helm/search_service_owner.asp?Style=helm&class_2=CHV Or if you are ok with hard books you ...
by br,lc,LA
Mon May 27, 2019 5:48 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

ACDELCO TDS... https://www.acdelcotds.com/subscriptions# The bottom of the page is a $20 3 day subscription that gets you to all the wiring diagrams and service manual info so you can look at routing photos. I normally only get the 3 day and just print to PDF everything I need in that time frame. If...
by br,lc,LA
Sat May 25, 2019 10:59 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

OneBFC wrote:Fun starts soon....wire looms, crimps and heat shrink are in your future!
Russ,

He took the easy route and had someone else build it for him... his fingers wont hurt like ours have hours of splicing and soldering!
by br,lc,LA
Fri May 10, 2019 4:12 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

Just going to express my opinion... take caution when dealing with AFI... they burned a few of us airboaters in the past.
by br,lc,LA
Thu Apr 25, 2019 7:30 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

Facebook Shane Lavalette
by br,lc,LA
Thu Apr 25, 2019 5:40 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

Ballistic makes a direct fit box for that motor
by br,lc,LA
Thu Apr 25, 2019 1:52 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

What you adapting to it?
by br,lc,LA
Mon Apr 22, 2019 2:53 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

If you have any issues with Swaptime, let me know. I have the wiring books for the 2.0 LTG. Its pretty much the same wiring as my LUV except with the addition of the direct injection components. Ill be on the water again mid-May. Taking care of my other hobbies and getting some things I wanted done ...
by br,lc,LA
Sun Apr 07, 2019 10:36 am
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LTG SWAP

You go it going right... you dont need the front mounts I have... I bought them just for pattern purposes on building the mounts you already have built. Good luck to you. I hope you give Jerry @ BNR a shout to tune it when you area ready. When you get down to wiring and needing to replicate the VSS ...
by br,lc,LA
Thu Apr 04, 2019 5:02 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LHU SWAP

I have a set of LTG front motor mounts ill give you so you can make patterns with them.

Custom build an idler... its easy.
http://www.exportedafrican.com/wordpress/
by br,lc,LA
Tue Mar 19, 2019 8:36 pm
Forum: Airboat Talk
Topic: Chuck. James Rackley
Replies: 39
Views: 4288

Re: Chuck. James Rackley

Any plans for a benefit ride and farewell? I know one was done several years back when he semi-retired.
by br,lc,LA
Tue Mar 19, 2019 8:19 pm
Forum: Automotive Power Only
Topic: ECOTEC 2.0 LTG SWAP
Replies: 166
Views: 8490

Re: ECOTEC 2.0 LHU SWAP

Ballistic is the only option for LTG unless you build adapters. LTG bellhousing pattern is different from other Ecotecs. Need to get a sealed gauge panel box such as a nema enclosure and run a Banks 1.8 IDash off the OBDII
by br,lc,LA
Mon Mar 18, 2019 8:04 pm
Forum: Airboat Talk
Topic: Chuck. James Rackley
Replies: 39
Views: 4288

Re: Chuck. James Rackley

Just saw this post. It was a pleasure to meet the man for sure.

Go to advanced search