Best way to remove old poly bolts?

A general, non-powerplant specific, discussion on airboat technology, ie., hulls, rigging, polymer, etc..
User avatar
pipedog
Site Supporter - III
Site Supporter - III
Posts: 2446
Joined: Mon Sep 06, 2010 6:28 pm
Location: Loxahatchee Fl

Best way to remove old poly bolts?

Post by pipedog » Sun Jan 26, 2014 10:02 am

I have a project boat and have to remove the poly, and so far has been a real son of a BI##H!! The bolts are stainless with lock nuts and philips head most are painted over. I got some out some stripped some snapped and I have 2 million to go :banghead: ...I also cut some but those bolts ate up a blade in no time :dontknow: ...any advice,tips,tricks,type of blades,anything will be appreciated!
Thanks .. :thumbleft:
Palm Beach open hull 13'9" with 6.0 F.I. LS - Ox Box and a 3bld "R"

User avatar
skinnypockets
Site Supporter - IV
Site Supporter - IV
Posts: 999
Joined: Mon Oct 18, 2010 8:12 am
Location: St Cloud, Fl

Re: Best way to remove old poly bolts?

Post by skinnypockets » Sun Jan 26, 2014 10:21 am

pipedog wrote:I have a project boat and have to remove the poly, and so far has been a real son of a BI##H!! The bolts are stainless with lock nuts and philips head most are painted over. I got some out some stripped some snapped and I have 2 million to go :banghead: ...I also cut some but those bolts ate up a blade in no time :dontknow: ...any advice,tips,tricks,type of blades,anything will be appreciated!
Thanks .. :thumbleft:
Kyle, Have you tried drilling the bolts from the head end?

:rebel: :florida: :old_glory:
I'VE DONE SO MUCH WITH SO LITTLE FOR SO LONG, I CAN DO ANYTHING WITH NOTHING!

13.6 Alumitec, 350 Chevy, Rotator Gearbox and 6 Blade Warp Drive

smessler34
Site Supporter - III
Site Supporter - III
Posts: 363
Joined: Sun Aug 17, 2008 8:08 pm
Location: Cocoa , FL

Re: Best way to remove old poly bolts?

Post by smessler34 » Sun Jan 26, 2014 10:29 am

I had the same problem.....i hit em with a propane torch, the a shot of PB blaster while they were hot , came right out....give it a shot,good luck

User avatar
Bruce
Site Supporter - IV
Site Supporter - IV
Posts: 4793
Joined: Tue Feb 27, 2007 9:43 pm
Location: orange county fl
Contact:

Re: Best way to remove old poly bolts?

Post by Bruce » Sun Jan 26, 2014 10:57 am

Back them off from the nut side
12 foot Mamba "The Underdog"
Tired Gpu 520,Whirlwind Razor X

dougeey
Site Supporter - I
Site Supporter - I
Posts: 601
Joined: Sat Sep 07, 2013 7:55 pm
Location: Red Level, Ala.
Contact:

Re: Best way to remove old poly bolts?

Post by dougeey » Sun Jan 26, 2014 11:13 am

They make a bit to remove striped out Philips get it at Sears. Hold the head and use a batt.impack to turn the nuts.

User avatar
pipedog
Site Supporter - III
Site Supporter - III
Posts: 2446
Joined: Mon Sep 06, 2010 6:28 pm
Location: Loxahatchee Fl

Re: Best way to remove old poly bolts?

Post by pipedog » Sun Jan 26, 2014 11:52 am

skinnypockets wrote:
pipedog wrote:I have a project boat and have to remove the poly, and so far has been a real son of a BI##H!! The bolts are stainless with lock nuts and philips head most are painted over. I got some out some stripped some snapped and I have 2 million to go :banghead: ...I also cut some but those bolts ate up a blade in no time :dontknow: ...any advice,tips,tricks,type of blades,anything will be appreciated!
Thanks .. :thumbleft:
Kyle, Have you tried drilling the bolts from the head end?

:rebel: :florida: :old_glory:
Haven't tried that yet, but that should work! I just tried a sawzall with a fine toothed blade called the torch and that worked pretty good, that blade lasted awhile.
Palm Beach open hull 13'9" with 6.0 F.I. LS - Ox Box and a 3bld "R"

User avatar
pipedog
Site Supporter - III
Site Supporter - III
Posts: 2446
Joined: Mon Sep 06, 2010 6:28 pm
Location: Loxahatchee Fl

Re: Best way to remove old poly bolts?

Post by pipedog » Sun Jan 26, 2014 11:56 am

smessler34 wrote:I had the same problem.....i hit em with a propane torch, the a shot of PB blaster while they were hot , came right out....give it a shot,good luck
smessler I should of mentioned that it if a fiberglass hull, so I'm afraid to put heat to it. Thanks for the input :thumbleft:
Palm Beach open hull 13'9" with 6.0 F.I. LS - Ox Box and a 3bld "R"

dougeey
Site Supporter - I
Site Supporter - I
Posts: 601
Joined: Sat Sep 07, 2013 7:55 pm
Location: Red Level, Ala.
Contact:

Re: Best way to remove old poly bolts?

Post by dougeey » Sun Jan 26, 2014 12:03 pm

Are you trying to save the poly. If not you can grind the heads off on poly. Side

User avatar
pipedog
Site Supporter - III
Site Supporter - III
Posts: 2446
Joined: Mon Sep 06, 2010 6:28 pm
Location: Loxahatchee Fl

Re: Best way to remove old poly bolts?

Post by pipedog » Sun Jan 26, 2014 12:08 pm

Bruce wrote:Back them off from the nut side
Hey Bruce I've tried ratchets, breaker bar's, electric impact, I just can't hold the philips head without stripping it :dontknow: ..So far the sawzall is the best, but I just started and have a sh!t load to go. I'm going to try drilling in the philips head next.
Thanks
Palm Beach open hull 13'9" with 6.0 F.I. LS - Ox Box and a 3bld "R"

User avatar
pipedog
Site Supporter - III
Site Supporter - III
Posts: 2446
Joined: Mon Sep 06, 2010 6:28 pm
Location: Loxahatchee Fl

Re: Best way to remove old poly bolts?

Post by pipedog » Sun Jan 26, 2014 12:16 pm

dougeey wrote:Are you trying to save the poly. If not you can grind the heads off on poly. Side
Hey Dougeey the poly is shot-out, so that is a damn good idea also :thumbleft: .. I did use a thin cutting wheel to cut the bolts, that worked good but ate-up the blades quick. I have a thick grinding wheel I can try :salute:
Thanks
Palm Beach open hull 13'9" with 6.0 F.I. LS - Ox Box and a 3bld "R"

dougeey
Site Supporter - I
Site Supporter - I
Posts: 601
Joined: Sat Sep 07, 2013 7:55 pm
Location: Red Level, Ala.
Contact:

Re: Best way to remove old poly bolts?

Post by dougeey » Sun Jan 26, 2014 12:51 pm

pipedog wrote:
dougeey wrote:Are you trying to save the poly. If not you can grind the heads off on poly. Side
Hey Dougeey the poly is shot-out, so that is a damn good idea also :thumbleft: .. I did use a thin cutting wheel to cut the bolts, that worked good but ate-up the blades quick. I have a thick grinding wheel I can try :salute:
Thanks
Your welcome if I still lived in wpb I would come over and help but got to many people living there now!!!

terrible ted
Southern Airboat Member
Posts: 2851
Joined: Tue Aug 12, 2008 8:07 pm
Location: orlando

Re: Best way to remove old poly bolts?

Post by terrible ted » Sun Jan 26, 2014 3:48 pm

well put your air gun on the nut and snap(tighten)as many as you can first. Stainless is soft not that hard.

barhopper
Site Supporter - II
Site Supporter - II
Posts: 712
Joined: Sat May 14, 2005 12:23 pm
Location: ocala

Re: Best way to remove old poly bolts?

Post by barhopper » Sun Jan 26, 2014 5:52 pm

I agree with Bruce and Ted. I've always used a impact wrench on the nut side with pretty good results. You'll always have some stubborn ones that require more effort. Will grinding them off on the poly side make the bolt hot enough to damage the fiberglass?

User avatar
TheElevatorGuy
Southern Airboat Member
Posts: 681
Joined: Mon Jul 16, 2012 8:24 pm
Location: Broward County

Re: Best way to remove old poly bolts?

Post by TheElevatorGuy » Sun Jan 26, 2014 6:18 pm

Hey Kyle........I have the quickest trick to get rid of all of the bolts at one shot................sell the hull :lol: :lol: :lol:

User avatar
pipedog
Site Supporter - III
Site Supporter - III
Posts: 2446
Joined: Mon Sep 06, 2010 6:28 pm
Location: Loxahatchee Fl

Re: Best way to remove old poly bolts?

Post by pipedog » Sun Jan 26, 2014 7:34 pm

Image
Palm Beach open hull 13'9" with 6.0 F.I. LS - Ox Box and a 3bld "R"

User avatar
pipedog
Site Supporter - III
Site Supporter - III
Posts: 2446
Joined: Mon Sep 06, 2010 6:28 pm
Location: Loxahatchee Fl

Re: Best way to remove old poly bolts?

Post by pipedog » Sun Jan 26, 2014 7:36 pm

Image
Palm Beach open hull 13'9" with 6.0 F.I. LS - Ox Box and a 3bld "R"

User avatar
pipedog
Site Supporter - III
Site Supporter - III
Posts: 2446
Joined: Mon Sep 06, 2010 6:28 pm
Location: Loxahatchee Fl

Re: Best way to remove old poly bolts?

Post by pipedog » Sun Jan 26, 2014 7:38 pm

Image
Palm Beach open hull 13'9" with 6.0 F.I. LS - Ox Box and a 3bld "R"

User avatar
pipedog
Site Supporter - III
Site Supporter - III
Posts: 2446
Joined: Mon Sep 06, 2010 6:28 pm
Location: Loxahatchee Fl

Re: Best way to remove old poly bolts?

Post by pipedog » Sun Jan 26, 2014 7:42 pm

Image
Palm Beach open hull 13'9" with 6.0 F.I. LS - Ox Box and a 3bld "R"

User avatar
pipedog
Site Supporter - III
Site Supporter - III
Posts: 2446
Joined: Mon Sep 06, 2010 6:28 pm
Location: Loxahatchee Fl

Re: Best way to remove old poly bolts?

Post by pipedog » Sun Jan 26, 2014 7:47 pm

Image
Palm Beach open hull 13'9" with 6.0 F.I. LS - Ox Box and a 3bld "R"

User avatar
Tony480
Site Supporter - I
Site Supporter - I
Posts: 5277
Joined: Sun Sep 10, 2006 5:52 pm
Location: lake county

Re: Best way to remove old poly bolts?

Post by Tony480 » Sun Jan 26, 2014 7:52 pm

Wow!! Not even the correct poly bolts....some people amaze me...

User avatar
pipedog
Site Supporter - III
Site Supporter - III
Posts: 2446
Joined: Mon Sep 06, 2010 6:28 pm
Location: Loxahatchee Fl

Re: Best way to remove old poly bolts?

Post by pipedog » Sun Jan 26, 2014 8:02 pm

Dark thirty but got it done!! some came off with the impact on the nuts like bruce said, tried that first on most, some would spin. Then I would put a breaker bar on the nut and use a drill with a philips bit and get some like that, if it stipped then I would grind, drill, sawzall the philips head off. It took alot of BEERs to get the job done but it was worth it :drunken: ...Thanks for all the input !!! :salute:
Palm Beach open hull 13'9" with 6.0 F.I. LS - Ox Box and a 3bld "R"

Airboat_Fever
Southern Airboat Member
Posts: 250
Joined: Thu Jan 05, 2012 3:10 pm
Location: Cedar Key Fl.

Re: Best way to remove old poly bolts?

Post by Airboat_Fever » Sun Jan 26, 2014 8:50 pm

i used an air impact on the phillips side and dad was on the inside with a socket and a wrench it worked pretty good but it definitely requires 2 people.
When No one else can get out I CAN!
___________________________
The VERY FIRST 13' Fiberglass AIRGATOR with Direct Drive Smallblock Chevy 72-32 paddle
in the works 10' 6in. by 7' Apache hull with 4.3 Direct Drive

User avatar
Hog Guts
Southern Airboat Member
Posts: 710
Joined: Sun Dec 15, 2013 10:20 pm
Location: Cocoa, FL

Re: Best way to remove old poly bolts?

Post by Hog Guts » Sun Jan 26, 2014 9:23 pm

Fire that up in the tree... Could be fun :)


Sent from my iPhone using Tapatalk

User avatar
pontoon outlaw
Site Supporter - IV
Site Supporter - IV
Posts: 1668
Joined: Fri Dec 04, 2009 7:56 pm
Location: palm bay, ride in Cocoa

Re: Best way to remove old poly bolts?

Post by pontoon outlaw » Sun Jan 26, 2014 9:45 pm

:scratch: WTH were those round head screws?? no wonder they were a bear, def rounded the threads down over time and insult to injury they used 2 peices of poly instead of just one whole sheet :violent1: good job man when I did mine the first time it had the old white poly on it, was brittle as hell, hammer and chissle to get poly off then vise grips on the stubborn bolts :thumbleft:

User avatar
Birddog247
Site Supporter - I
Site Supporter - I
Posts: 649
Joined: Mon Sep 07, 2009 9:12 pm
Location: Loxahatchee, FL

Re: Best way to remove old poly bolts?

Post by Birddog247 » Sun Jan 26, 2014 10:01 pm

Damm man

looks like you got a lot done. :thumbleft: you still want that sheet of poly I got?
12ft Palm Beach
stock 350sbc
2.1 gear/80"NGR

"Save a tree; eat a beaver"!

Post Reply

Return to “Airboat Tech”